The build of our 17' solid fiberglass, flat-bottom tunnel hull Garvey Skiff continues! In Part 5, Capt. Dan Berg from DIYeasycrafts continues fiberglassing the bow section of this custom-built project boat. We apply multiple layers of CMS mat and 1708 biaxial fiberglass cloth to build strength and create a solid composite hull. After the fiberglass cures, it's time to get the surface ready for the next stage. We use a 4" x 24" belt sander to knock down the high spots and smooth the fiberglass. We then apply Bondo short-strand fiberglass-reinforced filler to fill low areas and imperfections before sanding the bow again. All of this preparation is being done to get the hull ready for one of the next major steps in the build—installing four runners/rails on the bottom of the hull. In the next episode, we'll cut and shape the runners from Coosa Board, embed them in fiberglass resin, and fiberglass them securely into place on the hull bottom. This custom Garvey combines the classic sweeping Garvey bow with a flat bottom and tunnel hull designed for shallow-water operation. And because we're building it entirely from composite materials with no wood components, there will be no wood-rot concerns.
Back Bay Garvey Skiffs are a classic flat-bottom work boat traditionally built from wood. In this new boat-building series, Capt. Dan Berg from DIYeasycrafts takes the timeless Garvey design and reimagines it using modern composite materials and a few performance-enhancing modifications. This custom-designed 17-foot skiff retains the classic sweeping bow that made Garvey boats famous, while incorporating a tunnel hull design that allows the boat to operate in extremely shallow water. Unlike traditional wooden Garveys, this skiff will be constructed entirely from fiberglass and composite materials with no wood components, eliminating concerns about rot and significantly reducing long-term maintenance. In Part 1, we begin the build by fabricating the hull frame and constructing the transom using 3/4" Coosa Board. These components form the foundation of a durable, lightweight, and long-lasting skiff designed for years of service in back bays, rivers, and shallow-water environments. Follow along as we document every step of the build from design and construction through fiberglass layup, rigging, and sea trials.
In Part 3 of my custom 17-foot solid fiberglass flat-bottom tunnel hull Garvey Skiff build, it's time to start turning the lightweight core into a solid fiberglass boat. The Coosa Board and honeycomb core panels are first secured together with fiberglass tabs. Once the tabs cure, I remove all of the temporary screws that held the core material to the wooden frame. Every seam, joint, and exposed edge is then reinforced with CMS mat and 1708 biaxial fiberglass cloth. Finally, the entire honeycomb core is laminated with fiberglass mat and 1708. This not only adds stiffness to the hull but also seals the core, making it weather resistant so the project no longer needs to be covered with a tarp every time it rains. In the next episode, we'll continue building strength into the hull by applying multiple layers of fiberglass mat and 1708/1709 biaxial fiberglass to the tunnel, bottom, and sides of the boat. If you enjoy custom boat building, fiberglass fabrication, tunnel hulls, shallow water fishing boats, and DIY marine projects, be sure to subscribe so you don't miss the next installment of this build. 👍
How to build a 17' solid fiberglass flat bottom tunnel hull Garvey skiff.
In Part 4 of my 17' solid fiberglass flat-bottom Tunnel Hull Garvey Skiff build, we're adding serious strength to the hull with multiple layers of fiberglass. In this episode, I begin the main fiberglass layup at the transom and work forward toward the bow. Multiple layers of CMS fiberglass mat and 1708 biaxial fiberglass are applied using a wet layup technique to ensure the fiberglass is completely saturated and achieves the best possible bond to the hull. This fiberglass schedule will add strength, stiffness, and durability to this custom-built shallow-water tunnel hull skiff. It's a big step toward turning the core and framework into a strong, finished boat. In the next video, we'll finish up the fiberglass work on the bow section and start working on the runners for the bottom of the boat. If you're following this build from the beginning, check out the previous episodes to see how this unique 17' flat-bottom tunnel hull Garvey Skiff is coming together. 👍
How to make a Wind Screen Grab Bar for a Carolina Skiff J16 We purchased a Carolina Skiff J16 as a project boat. After doing some fiberglass repairs and modifications as well as making a lexan windshield we decided to built a wind screen grab bar out of 7/8 aluminum tubing. The grab bar is important because on these little skiffs something to hold onto is needed on even calm days. I used a pipe bender and standard hand railing fittings to create this grab bar.
Welcome back to the 17-foot solid fiberglass tunnel hull Garvey skiff build! In Part 6, we tackle the critical step of glassing the strakes onto the hull. Watch as we walk through the process of layout, shaping, transitioning corners cleanly, and laying down structural fiberglass to lock the strakes in permanently. Whether you're building your own custom shallow-water skiff, working with marine composites, or looking for tips on handling cloth and resin over sharp angles, this video covers the techniques you need for a bombproof finish. 🛠️ Catch up on the full build series: Check out the playlist on our channel to see everything from the initial scale models and framing to core installation and layup! Be sure to Like, Comment, and Subscribe for more custom boat building and DIY craft projects!
How to make a DIY Lexan windshield for a Carolina Skiff J16 We purchased a Carolina Skiff J16 as a project boat. After a bunch a small fiberglass repairs including making a honeycomb panel bow deck, bilge pump well, and rolling on fresh gelcoat I decided to make a windshield or wind screen. I purchased a sheet of 1/4 thick tinted lexan 18"x24" and some rubber grommets. We cut out a cardboard template and then cut and bent the lexan to shape. Check out this short how to video which details everything you need to know in order to build your own skiff windshield.
How to easily roll Gelcoat on a boat We purchased a Carolina Skiff J16 as a project boat. After a bunch a small fiberglass repairs we wanted to change the color and apply gelcoat. Dan Berg from www.DIYeasycrafts.com gives an overview of how easy this three step process is. We used gelcoat with wax waited for a non windy day. First step was to lightly sand with 80 grit then wipe down the hull with acetone. We rolled on three thin coats without waiting for the gelcoat to dry.
The classic Back Bay Garvey Skiff has been a favorite work boat for generations thanks to its flat-bottom design, shallow draft, and incredible stability. Traditionally built from wood, Capt. Dan Berg from DIYeasycrafts is building a modern version using composite materials that will never rot. This custom 17-foot Garvey Skiff features the traditional sweeping Garvey bow combined with a tunnel hull that allows the boat to run in even shallower water while maintaining excellent performance and stability. In Part 1, we built the hull framework and fabricated the transom from 3/4" Coosa Board. In Part 2, it's time to skin the hull. The frame is covered with Coosa Board and lightweight honeycomb core panels to create the foundation for the composite hull. The panels are temporarily fastened with screws to ensure everything stays perfectly aligned during assembly. Before fiberglassing begins, every temporary screw will be removed so the finished hull is 100% composite with no unnecessary fasteners trapped inside. Once complete, the entire hull will be fiberglassed inside and out to create a lightweight, incredibly strong, and completely rot-proof Garvey Skiff. If you're interested in fiberglass boat building, composite construction, or building your own custom fishing boat, this series will walk you through every step from the first frame to launching the finished boat.
How to make a bow platform for a Carolina Skiff out of strong lightweight honeycomb panels This short how-to video details how to make lightweight sturdy honeycomb bow platform for a Carolina Skiff J16. Dan Berg from www.DIYeasycrafts.com gives an overview of how he laminated the panels , used a cardboard template and then added support and attached the new structure to the hull. The end result is a bow casting platform that is strong, lightweight and will not become saturated or delaminate over time. We used fiberglass mesh for one side and biaxal, which is a combination of mesh and woven cloth combined with resin from totalboat to laminate the panels
How to make a Bilge Pump Well for a Carolina Skiff J16 Many Carolina Skiffs do not have a bilge well. In fact most have two scuppers which are located at or below the waterline. This lets an inch or water constantly on the deck. The solution is to install a bilge well, plug up the scuppers and let an automatic bilge pump pump the deck dry. This short how-to video details how to cut out and fiberglass a bilge pump well for a Carolina Skiff J16. Dan Berg from www.DIYeasycrafts.com gives an overview of how he cut through the deck and coated the box or well with fiberglass. He also installed plastic wood to screw down the bilge pump into and a top screen to prevent debris from clogging up the bilge.
How to easily make and work with Fiberglass Honeycomb Panels This short how-to video details how to make lightweight sturdy fiberglass honeycomb panels. Dan Berg from www.DIYeasycrafts.com demonstrates how to laminate the panels as well as how to finish the exposed ends. These panels are lightweight, strong and will not become saturated with water or delaminate over time. Perfect for boating projects. We used fiberglass mesh for one side and biaxal, which is a combination of mesh and woven cloth combined with resin from totalboat to laminate the panels